Skip to content
Metal roofing · Above grade

Your roof has one job.Toronto gives it a hard one.

Toronto metal roofing contractor: standing seam, metal shingles and ribbed steel, installed and repaired. We find out what is actually wrong before we tell you what to do.
Toronto / GTAStanding seam · Metal shingles · Repair
01 / The job

A metal roof is along-term decision.It should start withan honest look.

A Toronto roof sees freeze-thaw all winter, ice at the eaves, wind-driven rain and summer heat. Metal handles all of it well, if the deck under it is sound and the flashing is done right. We work in metal only, so that is all we think about.

02Metal roofing services

Metal roofs, installedand kept watertight.

From a full metal roof replacement in Toronto to a single flashing repair, each job starts with a proper look. Metal only: no asphalt shingles, no flat roofs.

White two-storey house with a dark grey standing seam metal roof
R1Semis, bungalows, century homes

Metal roof replacement

Toronto metal roof replacement

Most metal roofs we put on replace an asphalt roof that has worn out. We strip to the deck, check the boards underneath, and tell you what we find before any metal goes on.

  • Tear-off of the old roof, one layer or several
  • Deck repairs where boards have gone soft
  • Synthetic underlayment, ice-and-water at the eaves and valleys
  • New metal, trim and flashing in one system
Brown standing seam metal roof panels on a single-storey house, seen from above
R2

Standing seam

Concealed fasteners, clean lines

Long steel panels joined by raised seams, with the fasteners hidden under the seam. Nothing is exposed to the weather, so there is less to wear out. It is the most common choice for a house that wants a metal roof for the long term.

  • Snap-lock and mechanically seamed panels
  • Steel in a range of colours, aluminum on request
  • Ridge vents and snow guards where they belong
Metal tile roof with ridge trim, chimney caps and snow guards along the eaves
R3

Metal shingles and tiles

Metal that looks like a traditional roof

Interlocking steel panels pressed to look like shingles, shakes or tile, including stone-coated steel. A good fit for a street where a smooth standing-seam roof would stand out.

  • Shingle, shake and tile profiles
  • Stone-coated steel
  • Suits steep and cut-up roofs
House with a red corrugated metal hip roof and matching porch roof
R4

Ribbed steel panels

Exposed-fastener metal roofing

Ribbed or corrugated panels screwed through the face. The lowest-cost metal roof, and a sound one when it is installed and maintained properly. Common on garages, sheds, cottages and some houses.

  • Garages, sheds, porches and additions
  • 26-gauge for houses, lighter gauges for outbuildings
  • Fasteners and washers checked over time
Grey standing seam roof with a brick chimney, roof vents and valley and hip trim
R5Trace the water, not the stain

Metal roof repair

Some leaks start three metres from where you see them.

Metal roofs leak at the details, not in the middle of a panel: screws that have backed out, washers that have dried out, a seam that was never sealed, a flashing at a chimney or wall. We trace the water back, confirm the source, then fix that.

  • Loose or failed fasteners and washers
  • Seam, lap and trim leaks
  • Chimney, wall and skylight flashings
  • Storm and ice damage
R6

Flashing and trim

Roofs rarely fail in the open field. They fail where something interrupts the surface: a chimney, a wall, a valley, a vent, the eaves. On a metal roof the trim is part of the system, so it is bent and fitted to match.

Chimneys, walls, valleys, vents, ridge
R7

Eavestrough, soffit and fascia

The roof edge that throws water clear of the walls and foundation. We supply and install seamless aluminum eavestrough and downspouts, and metal soffit and fascia, with the roof or on their own.

Seamless 5" and 6" eavestrough
FIG. 02Roof anatomy

Six parts.One roof.

Pick a part. See what it does, and what failure looks like on a Toronto house.

What it does

Shed water, snow and ice down and off the roof. On standing seam the fasteners sit under the raised seams, out of the weather.

What failure looks like

On exposed-fastener panels: screws that back out and washers that dry and crack, letting water in at each hole. On any metal roof: scratches left to rust, and panels that were fastened too tight to move with the heat.

Schematic only. Real roofs vary by house.

What would a metal roof cost?

A rough range from typical Greater Toronto Area prices: low-end to high-end materials, mid-range labour. No email needed. Nothing you enter leaves this page unless you send it to us.

ROUGH ESTIMATE / GTA MARKET RATESNot a quote
Type of metal
sq ft

The ground-floor outline of the house, including an attached garage if it shares the roof. Not the total living area.

How steep is the roof?
Roof shape
Storeys
Old roof to remove?
ExtrasLeave at 0 if not needed. Measure along the edge of the roof.
ft

Includes taking the old ones down.

ft

Aluminum, vented soffit.

Chimneys
0
Skylights
0
Rough estimateNot a quote

$ – $

CAD, before HST

Standing seam steelabout 1,490 sq ft of roof
$22,050–$35,500
Tear-off and disposal, one layerabout 1,490 sq ft
$1,450–$1,500
  • Includes underlayment, ice and water protection at eaves and valleys, standard trim and fasteners.
  • Rotten roof boards found during tear-off are extra, priced per sheet on the day.
  • Aluminum standing seam costs more, roughly $22–30 per sq ft installed.

Want a real number? We come out, measure and give you a written quote.

Get a proper estimate

Rough estimate only, not a quote. Based on typical Greater Toronto Area prices for comparable work in 2026. Your price depends on what we find on site.

Rough estimate $23,500 to $37,000, before HST.
A row of red-brick bay-and-gable Victorian houses on a tree-lined Toronto street
03Toronto housing

Toronto homes aren'tall built the same.

Semis and bay-and-gables
Steep gables, valleys and brick chimneys. Metal shingles or narrow standing seam, with the flashing done properly at every join.
Bungalows
Big, simple roof areas. Ideal for standing seam: long, straight runs with few cuts.
Century homes
Old decking and layers of earlier roofs. We find out what is under the old roof before we price the new one.
Garages and additions
Ribbed steel panels on outbuildings and sloped additions. Low cost, long life, little upkeep.
04Metal roofing projects

Roofs we haveput right.

Stand-in examples showing how a roofing project is documented. Real Reno the 6ix jobs replace these.

Sample projectsAll work
05 / FAQ

Metal roofing questions,answered plainly.

General answers. Your house gets a specific one after we have seen the roof.
01

Do you install asphalt shingles or flat roofs?

No. Our roofing work is metal only: standing seam, metal shingles and tiles, and ribbed steel panels, plus the flashing, eavestrough, soffit and fascia that go with them. We also repair metal roofs. If your home needs asphalt shingles or a flat-roof membrane, we will tell you so and suggest you speak to a specialist in that.

02

How much does a metal roof cost in Toronto?

It depends on the metal, the size and pitch of the roof, how cut-up it is, and what has to come off first. As a rough guide, installed metal roofing in the GTA usually runs from about $8.50 per square foot of roof for ribbed steel panels to $22 or more for standing seam, before HST. Use the estimator on this page for a range for your house, then we confirm it after seeing the roof.

03

Is metal roofing worth it over asphalt shingles?

A metal roof costs more up front, but it typically lasts several times longer than an asphalt roof, sheds snow, and needs little upkeep beyond checking the trim and fasteners. If you plan to stay in the house, it often works out cheaper over the life of the roof. If you are selling soon, the numbers are less clear and we will say so.

04

Is a metal roof noisy in the rain?

Not on a house. Installed over a solid deck with underlayment and an insulated attic, rain on a metal roof sounds much like rain on any other roof. The loud drumming people remember is usually from metal on open framing, such as a barn or shed.

05

Can you put a metal roof over my old shingles?

Sometimes it is allowed, but we usually recommend a tear-off. It lets us check and repair the deck, keeps the weight down, and gives the new roof a flat surface to sit on. We will tell you after the assessment if going over the old roof is a reasonable option for your house.

06

Can a metal roof be installed in winter?

Often, yes. Unlike asphalt shingles, metal does not rely on warm weather to seal, so planned work can carry on through much of the winter. Snow, ice and wind still affect safety and pace, so we schedule around the forecast and tell you honestly if a job should wait.

07

Why does my metal roof leak only in some weather?

Leaks often show up only with wind-driven rain, melting snow or ice, because those push water to places normal rain does not reach: a lap, a fastener, a flashing at a wall. That also makes them hard to find from a single visit, so we trace the path of the water rather than guess from the stain.

08

Do I need a permit for a metal roof in Toronto?

Often a re-roof does not need a building permit, but it depends on the work. Changing the roof structure, adding or enlarging openings, or structural repairs usually do. Rules vary by municipality and change over time, so confirm with the City of Toronto or your local building department, and we will flag it during the assessment if your job looks like it needs one.

06 / Next

How much metal roofare we talking about?

Get a rough price range from the estimator, or skip ahead and tell us what is going on. Either way, a person looks at the house before any number is final.

Estimator figures are a rough range, not a quote.